Digital PS-2000B Series Instalační příručka stáhnout pdf

PS-2000B Series

Installation Guide

Follow the instructions given below to ensure the correct and safe use of the PS-B.

• If the screen becomes dirty or smudged, moisten a soft cloth with diluted neutral deter-

gent, wring the cloth well, and wipe the display. Do not use thinner or organic solvents.

• Avoid storing and operating the PS-B in direct sunlight, high temperatures and

humidity, and in areas where excessive dust and vibration will occur.

• Avoid using the PS-B in areas where sudden, extreme changes in temperature can occur.

This may cause condensation to form inside the unit, possibly leading to an accident.

• To prevent the PS-B from overheating, be sure its air circulation vents are clear

and clean, and keep the unit’s operation area well-ventilated.

• Avoid operating or storing the PS-B near chemicals, or where chemicals can

come into contact with the unit.

• The Digital Electronics Corporation cannot be held responsible or provide any

compensation for damage(s) caused by the loss of data stored in the PS-B unit’s

hard disk drive (HDD). It is therefore strongly suggested that all important data

and software be backed up regularly to an external data backup device.

• After turning OFF the PS-B's power, wait until the internal HDD stops spinning

before turning the power ON again (approx. 5 seconds).

To Prevent Accidents

Follow the instructions given below to ensure the correct and safe use of the PS-

2000B Series unit, hereafter referred to as the “PS-B”.

• To prevent an electrical shock, be sure to connect the power cord to the PS-B

before connecting it to the main power supply.

• A fire or electrical shock may result if voltages are used with the PS-B that are

beyond the specified range. Be sure to only use the specified voltage.

• Before opening the PS-B’s protective cover, be sure to turn the unit’s power OFF.

This is because the PS-B’s internal parts carry high voltages.

• If metal particles, water or other types of liquids contact any of the PS-B’s internal

parts, immediately turn the unit’s power OFF, unplug the power cord, and contact

your local PS-B distributor.

• Read and understand Chapter 4 “Installation and Wiring” thoroughly in order to

select an appropriate installation location for the PS-B.

• Before either plugging in or unplugging an expansion board or interface connec-

tor, be sure to turn the PS-B’s power OFF.

• To prevent a possible explosion, do not install the PS-B in areas containing flammable

gases.

• The PS-B is not appropriate for use with aircraft control devices, aerospace equip-

ment, central trunk data transmission (communication) devices, nuclear power

control devices, or medical life support equipment, due to these devices’ inher-

ent requirements of extremely high levels of safety and reliability.

• When using the PS-B with transportation vehicles (trains, cars and ships), disas-

ter and crime prevention devices, various types of safety equipment, non-life

support related medical devices, etc. redundant and/or failsafe system designs

should be used to ensure the proper degree of reliability and safety.

WARNINGS

1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - WARNINGS

1PS-2000B SeriesInstallation GuideFollow the instructions given below to ensure the correct and safe use of the PS-B.• If the screen becomes dirty or

Strany 2 - CE Marking Notes

10 External Input Signal (Dual use of DIN, RST Input Port)• General Purpose Input (DIN)’s input level must be 1.5 seconds or longer tobe detected

Strany 3 - Package Contents

115 Installing the PS-B1) Use the four (4) attachment screws included in the PS-B’s packing box toattach the mounting brackets to the PS-B main unit.

Strany 4 - About The Manual

122) Drill the attachment holes in the panel. Be sure to follow the dimensionsgiven for the attachment holes.(Unit : mm [in.] - excluding projections)

Strany 5 - 1 PS-B External Features

136 Wiring the PS-BWARNINGS• To prevent electric shocks, be sure to turn the PS-B's power supplyOFF before connecting the power cord.• To avoid t

Strany 6 - 2 PS-B Dimensions

141) Confirm that the PS-B unit’s power supply is turned OFF.2) Use a screwdriver to remove the Power Input Terminal Block’s clear plasticcover.3) Uns

Strany 7 - 3 General Specifications

157 Power Supply Cautions• If voltage fluctuations are expected to varybeyond the specified range, connect a constantvoltage transformer.• Use a low-n

Strany 8 -  Structural

168 Grouding Cautions9 Cautions When Connecting I/O Signal LinesPS-BOtherdeviceOtherdeviceOtherdevice• Set up a dedicated ground whenusing the front p

Strany 9 - 4 Interface Specifications

2The PS2000B-41 units are UL/c-UL 60950 recognized products. (UL File No. E171486). Pleasepay special attention to the following instructions when app

Strany 10 -  RAS Interface

3Package ContentsThe PS-B package should include the following items:• Be careful when installing the PS-B not to damage the built-in HDD.• This cord

Strany 11 - 5 Installing the PS-B

4The PS-B unit’s CD-ROM contains the following PDF manual files.- PS-2000B Series User Manual- PS-2000B Series RAS-API Reference ManualReading a PDF f

Strany 12 - Horizontal Installation

51 PS-B External Features• To prevent an electrical shock, be sure to disconnect the PS-B’s power cordfrom the power supply before connecting the cord

Strany 13 - 6 Wiring the PS-B

62 PS-B Dimensions(Unit: mm [in.]- excluding projections)Side ViewTop ViewFront View118 [4.65]265 [10.43]260[10.24]39[1.54]Dimensions including option

Strany 14 - 3.2 mm or larger

7 Electrical Environmental3 General SpecificationsRated Voltage AC 100V/AC 240VAllowable VoltageRangeAC 85V to AC 265VRated Frequency 50/60HzAllowab

Strany 15 - 7 Power Supply Cautions

8 StructuralGroundingExclusive grounding only.Less than 100Ω, or your country’s applicable standard.Installation Method Inside a solidCooling Method

Strany 16 - 8 Grouding Cautions

94 Interface Specifications RS-232C Interface (COM1/COM2/COM3/COM4)Pin No.SignalNamePin No.SignalName1CD6DSR2RXD7RTS3TXD8CTS4DTR9RI/+5V5GNDDsub 9 pin