Digital DEClaser 3500 Specifikace Strana 166
- Strana / 442
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 6: FRU Replacement and Fault Isolation Procedures
6-38
6.2.19 Inoperative Drive Assembly
NOTES:
DO NOT USE THIS FIP if the Diagnostic tool is not available. Go to Section 6.3.17
Drive
Assembly failure.
1. INITIAL ANALYSIS
Inspect the following components. Are they compatible with your printer version, correctly
installed, not damaged, deformed, or contaminated?
• MCU PWB
• Drive Assembly
• LVPS Assembly
Inspect the printer paper path. Is it clear of foreign matter, such as staples, paper clips, and
paper scraps?
Yes No
Go to Step 2. Replace the problem components.
2. MAIN MOTOR ANALYSIS
Use Diagnostic Tool Test DG90 to check the Main Motor function.
Does the Main Motor function correctly?
Yes No
Replace the MCU PWB. Go to Section 6.3.17
Drive Assembly Failure.
- DEClaser 3500 Printer 1
- Service Guide 1
- Canadian Notice 4
- Avis Canadien 4
- Acoustics 4
- Minimum Space Requirements 20
- Functional specifications 21
- Physical Specifications 22
- Media specifications 23
- Top or face sheet 24
- Carrier or Backing Sheet 24
- Adhesive 24
- Physical Description 28
- Rear View of Printer 29
- Paper Transportation 32
- Fusing and Paper Exit 34
- Electrical Module 38
- Options 40
- Control Panel Keys 42
- Restoring Factory Defaults 45
- Printing the Menu Map 45
- Level 1 Menu Map 45
- Level 2 Menu Maps 47
- OPTIONAL 48
- **OPTIONAL 49
- RESETS TIME-OUTS 50
- SETTINGS 50
- POST Modes 52
- Status Messages 53
- Operational Warning Modes 55
- Operational Error Modes 56
- No Paper Sensor Failure 57
- System Error Modes 62
- System Failure Mode 65
- Demo Mode 68
- Error Codes 70
- 850, 851, 852, 853, 854 73
- 855, 856, 857, 860, 861, 862 73
- Procedures 78
- Normal Operations 80
- Problems 81
- D. Jam FIPs 92
- E. Image Quality FIPs 95
- Maintenance 101
- Cables and Adapters 101
- Chapter 5 : Wiring Diagrams 102
- Chapter 5: Wiring Diagrams 104
- Section 3 Parts List 107
- Isolation Procedures 129
- ROS Assembly Failure 131
- Scanner Assembly Failure 131
- Continued 132
- Heater Rod Assembly Failure 133
- Temperature Sensor Assembly 134
- Failure 134
- (Close Front Cover) 135
- E4 continued 137
- Fault code E3 139
- Fault code E3 continued 140
- Drive Assembly Failure 141
- Pick–Up Solenoid Failure 143
- Paper Size Switch Failure 144
- No–Paper Sensor Failure 144
- Feed Solenoid Failure 145
- Turn Solenoid Failure 145
- CRU Switch Failure 147
- MBF Sensor Failure 151
- Fault code J5 155
- Fault code J5 Continued 156
- 6.2.15 Inoperative Printer 157
- 6.2.16 Malfunctioning LCD 161
- 6.2.17 Inoperative key pad 163
- 6.2.18 Erratic operation 165
- Assembly failure 166
- 6.2.20 Inoperative Fan 167
- ROS Assembly failure 170
- 6.3.4 ROS Assembly failure 172
- LVPS Assembly Failure (+5VDC) 173
- 6.3.5 Heater Rod Failure 175
- 6.3.7 Exit Sensor failure 179
- 6.3.9 MBF Sensor failure 183
- LVPS Assembly Failure (+24VDC 193
- 6.3.19 HVPS CR (DC) failure 204
- 6.3.20 HVPS DB failure 206
- 6.3.21 HVPS TR failure 208
- 6.3.22 Noise 210
- 6.3.22 Noise Continued 211
- Image Quality Problems 213
- 6.4.1 Light prints 214
- HVPS DB Failure 215
- HVPS TR Failure 215
- 6.4.2 Blank prints 216
- 6.4.3 Black prints 218
- 6.4.7 Vertical streaks 223
- 6.4.8 Horizontal streaks 225
- 6.4.9 Spot deletions 227
- 6.4.10 Spots 229
- 6.4.11 Residual image 230
- 6.4.12 Background 232
- 6.4.13 Skewed image 233
- 6.4.14 Damaged prints 234
- 6.4.15 Unfused image 235
- The Diagnostic Tool 236
- Printer Modes 236
- Entering a Printer Mode 236
- ESS (Controller) Mode 237
- User Operation Mode 238
- User Operation Mode options 238
- Front Tray Size 241
- Universal 241
- Printing Test Mode 242
- To enter Printing Test Mode 242
- Diagnostics Mode 243
- To Enter Diagnostics Mode 243
- Diagnostic Code Table 244
- DG 30 PRINT COUNTER 246
- DG 02 Sensor Check 247
- Output Tests 248
- DG 07 FUSER TEMP. SET 249
- DG 08 FUSER TEMP 250
- DG 80 SOLENOID TRAY 0 252
- DG 81 SOLENOID TRAY 1 252
- DG 86 SOLENOID TRAY 2 253
- DG 84 T CLUTCH UPPER 253
- DG 85 T CLUTCH LOWER 254
- DG 90 MOTOR MAIN 254
- DG 91 HVPS (C. ROLL AC) 255
- DG 92 HVPS (C. ROLL DC) 256
- DG 93 HVPS (DEV BIAS) 257
- DG 94 HVPS (T. ROLL -) 258
- DG 95 HVPS (T. ROLL +) 259
- DG 00 EXIT DIAG 260
- DG 00 SIZE SENSOR 261
- DG 00 Exit 262
- Diagnostics 262
- DG 00 CHECK SUM 263
- Configuration Mode 264
- Configuration Mode options 264
- To enter Configuration Mode 264
- To input code parameters 265
- Fault and Status Codes 269
- Printing Controls 274
- ROS Controls 276
- Fuser Controls 277
- PL1 Covers 281
- PL2 Paper feed 283
- PL3 Paper transportation 285
- PL3 Paper Transportation 286
- PL4 Fusing and paper exit 287
- PL4 Fusing and Paper Exit 288
- PL6 Electrical module 291
- FIC/Xerox Spares 297
- Third-Party Spares: 297
- Procedures — Covers 298
- RRP 1.1 Rear Cover 299
- RRP 1.2 Top Cover Assembly 301
- RRP 1.3 Left Cover 303
- RRP 1.4 Right Cover 305
- Procedures — Feeder Assembly 307
- RRP 2.1 Feeder Assembly 308
- RRP 2.2 Feed Solenoid 310
- RRP 2.3 Turn Solenoid 312
- RRP 2.4 Feed Roll Assembly 314
- RRP 2.5 Feed Roll 316
- RRP 2.6 Turn Roll Assembly 318
- RRP 2.7 No-Paper Actuator 320
- RRP 2.8 Feeder PWB 322
- RRP 2.9 Size Spring 324
- Chapter 11 : Removal and 326
- Transportation 326
- RRP 3.1 Link Assembly 327
- RRP 3.2 Gear Double L 329
- RRP 3.3 Gear Double R 331
- Replacement 334
- RRP 3.7 BTR Assembly 339
- RRP 3.13 Pick–Up Solenoid 351
- RRP 3.15 MBF Sensor 355
- RRP 3.17 Console Assembly 359
- Chapter 12 : Removal and 363
- RRP 4.1 Fuser Assembly 364
- RRP 4.2 Pressure Roll 366
- RRP 4.3 Exit Chute 368
- RRP 4.4 Exit Roll Assembly 370
- RRP 4.6 Heater Rod 374
- RRP 4.7 Heat Roll 376
- RRP 4.8 Exit Actuator 378
- RRP 4.9 Exit Sensor 380
- Chapter 13 : Removal and 382
- Xerographic Modules 382
- RRP 5.1 Drive Assembly 383
- RRP 5.2 CRU Sensor PWB 385
- RRP 5.4 Scanner Motor 389
- RRP 5.5 ROS Assembly 391
- RRP 6.2 Controller (ESS) 400
- RRP 6.5 MCU PWB 406
- RRP 6.6 HVPS 408
- RRP 6.7 LVPS Assembly 410
- RRP 6.8 Fan 412
- Procedures — Options 414
- Troubleshooting 420
- Replacement: 427
- Training 428
- Environment 433
- DEClaser 3500 Country Kits 435
- (Not Orderable) 439
Související produkty a manuály pro Tisk a skenování Digital DEClaser 3500
Tisk a skenování Digital LA30W Servisní příručka
(107 stránky)
(107 stránky)
Tisk a skenování Digital LA30W Servisní příručka
(141 stránky)
(141 stránky)
Tisk a skenování Digital LA30W Uživatelský manuál
(46 stránky)
(46 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce